Scavini in the UAE & Gulf.
Chemparts Middle East is the authorized regional distributor of Scavini — bench-top petroleum testing. We supply, install, calibrate and service Scavini equipment across the UAE (Dubai, Abu Dhabi, Sharjah), Qatar and the wider Gulf, with genuine spares and full manufacturer warranty.
58 Scavini products in stock.
Instruments, spares and consumables from Scavini, held in the region. Pricing and lead-time on request.
Abel Flash Point Tester
Manual equipment with the heating bath realized exactly as reported in the IP 33 - IP 170 methods and equipped with electric heating, digital temperature display, gas ignitor and electric stirrer
Aging Oils
The apparatus consists of a benchtop case hosting the heating block and a frame supporting the stirring mechanism. The block has a series of jackets for the sample containers: a turntable permits to assemble the sample containers before putting them in the jackets all together. The block can reach temperatures up to 150°C +/- 0.1°C: it is heated by means of a coaxial heater. The stirring device is actuated by means of an electronically piloted gear reduced motor connected to a cam: it is regulated for 25 rpm.
Anti-Rust Power Of Oils
The apparatus consists of a benchtop case containing a dry block heater or a stainless steel tank and a support for the stirrer motors. Each position is equipped with an independent motor: in this way it is possible to use single positions and leave turned off the motors of the positions not used.
Anti-Rust Power Oils
The apparatus consists of a floor mounted case containing a stainless steel tank and the rotating mechanism. A control box located on the right side contains all the electronics.
Apparatus Determination Evaporation Loss Of Greases And Oils
The apparatus, in acc. with ASTM D 972 – IP 183, consists of a case containing a stainless steel bath and supporting precision flowmeters. The bath is equipped with a stainless steel cover with holes for the introduction of the evaporation cells.
Apparatus Determination Hihg Temperature Evaporation Loss
The apparatus, in acc. with ASTM D 2595, consists of a case hosting the aluminium block and supporting precision flowmeters. The block has jackets for the introduction of the cups: the air preheater is in the bottom. Each position is equipped with a digital display, connected to a thermocouple, that continuously shows the temperature of the air coming out from the cell.
Apparatus For Determination Of Freezing Point Of Antifreeze
The only equipment on the market fully acc. to ASTM D1177 (other equipment available frequently use the ASTM D2386 sample volume that is 25 ml while D1177 prescribes 75 to 90 ml) is equipped with an integrated cryostat capable to reach -120°C, sample and seeding jacket, touch-screen interface, Ethernet and two USB ports to connect printers or LIMS. The built-in seeding jacket permits to avoid the need of a powerful cryostat to freeze the sample portion requested for seeding.
Apparatus For Determining The Thin Film Volatility Of Bitumen
The apparatus, in acc. with ASTM D 2872 - EN 12607, consists of a forced air circulation oven suitable for temperatures up to 180°C and equipped with a rotating shelf placed inside along with a coil that preheats the air directed into the sample container. This test is used to determine the effect of heat and air on a moving film of semi-solid asphaltic materials. The effects of this treatment are determined from measurements of the properties of the asphalt before and after having heated in a oven for 75 minutes at 163°C a moving film of asphaltic material while air at a rate of 4 l/min is directed against the sample.
Automated Foaming Test Apparatus
Twin units can be equipped with variable area flowmeters or with mass-flow controllers and touch-screen interface capable to automatically blow the requested air amount into the sample in the prescribed amount of time, save and store data, print test reports.
Automatic Apparatus For Determination The Point Of Sliding And Turbidity Of Products Petroleum
Innovative, small size stand-alone equipment acc. to ASTM D 97 and D 2500 - IP 15 and 219 - ISO 3015 and 3016 with touch-screen interface and integrated cryostat (CFC/HCFC free) capable to reach -120°C. USB and Ethernet ports permits to connect printer or link the instrument to LIMS.
Automatic Apparatus For The Determination Of The Pour Point Of Petroleum Products
Innovative, small size stand-alone equipment acc. to ASTM D 97 - IP 15, ISO 3016 with touch-screen interface and integrated cryostat (CFC/HCFC free) capable to reach -120°C. USB and Ethernet ports permits to connect printer or link the instrument to LIMS.
Automatic Demulsivity Tester
Automatic instrument with four independent positions and CCD camera that continuously monitors the oil/water separation: pictures taken at 5-min intervals are saved and printed as test reports.
Automatic Equipment For Determination Of Freezing Point
Innovative, small size stand-alone equipment acc. to ASTM D 2386 - IP 16 with touch-screen interface and integrated cryostat (CFC/HCFC free) capable to reach -120°C. USB and Ethernet ports permits to connect printer or link the instrument to LIMS.
Automatic Equipment For The Determination Of CFPP Of Gas Oil
Innovative small size stand-alone equipment acc. to ASTM D 6371, IP 309, EN 116 and UNI EN 16329 (step cooling) with touch-screen interface, Ethernet and USB port. The integrated cryostat is completely CFC/HCFC free.
Automatic Equipment For The Determination Of The Cloud Point Of Oil Products
Innovative, small size stand-alone equipment acc. to ASTM D 97 - IP 15, ISO 3016 with touch-screen interface and integrated cryostat (CFC/HCFC free) capable to reach -120°C. USB and Ethernet ports permits to connect printer or link the instrument to LIMS.
Automatic Equipment For The Determination Of The Softening Point Of The Ball And Ring Bitumen Method
The apparatus, in acc. with ASTM D 36 - IP 58 - ISO 4625 is a benchtop model which houses the components and a Panel PC with touch screen. A software running under Microsoft Windows embedded permits to select the test method and the test parameters, run the test automatically, store, retrieve and print data, diagnose and calibrate the instrument offering in the meanwhile all the features of Windows systems such as LAN connectivity. Besides, a unique cooling system, not fitted on other instruments permits to quickly cool down the sample allowing to handle the glassware and to perform a greater number of tests during a day by reducing the dead times between two analysis. The apparatus is suitable also to test coating mixtures and other materials different from bitumen. The softening point is the temperature at which a disk of the sample held within a horizontal ring is forced downward a distance of 25.4 mm under the mass of a steel ball as the sample is heated at a prescribed rate in a water or glycerine bath.
Automatic Pensky Martens Flash Point Tester With Barometric Correction Of The Result
The only equipment on the market with the stove, air bath and top plate manufactured exactly as reported on the ASTM D 93 method. The instrument features electric heating, stirrer and dipping mechanism, barometric temperature correction, plus a touch-screen interface that permits to introduce test data, save and retrieve reports, print them and allow diagnostic and calibration.
Cloud And Pour Point Benchtop Cabinet
The first compact benchtop Cloud and Pour Point bath on the market with Stirling cooling compressors capable to reach -70°C. One, two, three four and five-position units available with four or eight jackets for each temperature. Compact, reliable, modern, smart. ... Cloud and pour point bath consists of a small benchtop unit with one, two, three, four or five groups of four or eight jackets: each group is equipped with a dedicated Stirling cooling compressor capable to reach -75°C. Electronic controllers permit to keep the temperatures stable with +/0,1°C accuracy while a defrosting device maintain the top surface free from condensing humidity and icing. Powder coated compact benchtop case. Insulating acrylic cover with insulated lids. Defrosting device that keeps the top surface free from condensing water and icing. Aluminium jackets, four or eight for each temperature. One dedicated Stirling liquid-helium cooling compressor for each group of jackets: temperature range: from ambient to -75°C. One thermometer jacket for each group of jackets. Microprocessor thermoregulators with PID action and built-in digital display 0.1°C accuracy. Probe: Pt100 RTD. Anodized aluminium control panel with engraved indications and dedicated switches for each temperature. Easy access control box. English written user's guide and installation instructions. For 220 V/50-60 Hz connections. Power consumption 150W (single unit) to 800 W (fiveposition unit). CE marked. One, two, three, four and five-block units available with either four or eight jackets for each temperature: custom units upon request. Cloud and pour point bath CAPP-104 Single unit (one group of four jackets). Dimensions: 420 x 420 x 500 mm, 15 kg approx. Cloud and pour point bath CAPP-204 Twin unit (two groups of four jackets). Dimensions: 560 x 420 x 500 mm, 32 kg approx. Cloud and pour point bath CAPP-304 Three-position unit (three groups of four jackets). Dimensions: 560 x 640 x 500 mm, 62 kg approx. Cloud and pour point bath CAPP-404 Four-position unit (four groups of four jackets). Dimensions: 560 x 640 x 500 mm, 68 kg approx. Cloud and pour point bath CAPP-504 Five-position unit (five groups of four jackets). Dimensions: 1200 x 420 x 500 mm, 80 kg approx. Cloud and pour point bath CAPP-108 Single unit (one group of eight jackets). Dimensions: 480 x 420 x 500 mm, 18 kg approx. Cloud and pour point bath CAPP-208 Twin unit (two groups of eight jackets). Dimensions: 680 x 420 x 500 mm, 42 kg approx. Cloud and pour point bath CAPP-308 Three-position unit (three groups of eight jackets). Dimensions: 680 x 640 x 500 mm, 74 kg approx. Cloud and pour point bath CAPP-408 Four-position unit (four groups of eight jackets). Dimensions: 680 x 640 x 500 mm, 80 kg approx. Cloud and pour point bath CAPP-508 Five-position unit (five groups of eight jackets). Dimensions: 1200 x 420 x 500 mm, 95 kg approx. ACCESSORIES Cloud and pour point bath CAL001 PT100 simulator CAL003 Official Certificate for Pt100 simulator CONSUMABLES Cloud and pour point bath AD0097-C00 Test jar with sample level graduation AD0097-C01 Centrally bored cork for test jar AD0097-C02 Gasket for test jar AD0097-C03 Disk (to be placed on the bottom of the jacket) TA005C-N00 ASTM 5C thermometer (-38°C/+50°C) TA006C-N00 ASTM 6C thermometer (-80°C/+20°C) Specifications Cloud and pour point bath may vary without notice. Cloud and pour point bath is supplied bare without glassware, diffusers, accessories and consumables.
Computer Controlled Ductility Machine
The apparatus, in acc. with ASTM D 113, D 5976 - IP 32 - ISO 1208 EN 13398, 13589, 13703 consists of a constant temperature bath capable to work in the range from -10 to 40 °C (thanks to a built-in cooling compressor) with an electrically powered tractor that pulls apart at an selectable speed the two ends of two briquet specimens: a load cell records continuously the force applied to the briquets transmitting them plus the bath temperature and the carriage speed to a PC through the RS-232 serial interface or USB port (converter required): a data acquisition software permits to display data on graphs, store them on the hard-disk, obtain printed reports and calibrate temperature, force and elongation sensors.
Copper Corrosion Of LPG
The apparatus consists of a benchtop steel case containing a stainless steel bath with a cover with up to eight jackets that allow the introduction of the vessels and a control box containing all the electronics.
Corrosion Foil Silver
The apparatus, suitable for the execution of the test at 50°C, consists of a steel case containing a stainless steel bath with a four-hole cover for the test tubes and a manifold for connecting water to the condensers.
Corrosion On Aluminum
The apparatus consists of a base supporting one or two heat-transfer corrosion cells. Cells are rated for a working pressure up to 40 psi and working temperature up to 160 °C. An electronic timer permits to set the test duration while an electronic thermostat is used to control the temperature.
Corrosion On Copper Foil
The apparatus, suitable for the execution of the test at 40, 50 and at 100°C, consists of a benchtop steel case containing a stainless steel bath with a four-hole cover to allow the introduction of the vessels or the test tubes and a control box containing all the electronics.
Corrosione Su Lamina Di Rame E Argento
The apparatus, consists of a benchtop steel case containing a stainless steel bath: the cover has a series of holes suitable for both glassware for copper and silver strip corrosion tests and vessels for copper strip corrosion test. Two manifolds permit to easily connect cooling water to silver corrosion glassware.
Demulsibility Mechanical In Oil Lubricants D 2711
Four-place apparatus acc. to ASTM D 2711 with electric lifting mechanism, digital tachometer, adjustable speed electric stirrer, electronic temperature controller, level and overtemperature alarm. Differently from many equipment on the market having electronics placed on the top cover and subject to overheating and ageing, ours has a separate control box placed on the right side of the instrument.
Determination Foaming Bath
Single-unit apparatus with two jackets acc. to ASTM D 892 - IP 146 for tests at 24 and 93.5°C. Equipped with electronic temperature controller, variable area flowmeters, level and overtemp alarm. Differently from many equipment on the market having electronics subject to overheating and quick ageing because placed on the bath cover, ours has a separate control box placed on the right side of the instrument.
Determination Water Separability D 1401
Six-place apparatus acc. to ASTM D 1401 with electric lifting mechanism, digital tachometer, adjustable speed electric stirrer, electronic temperature controller, level and overtemperature alarm. Differently from many equipment on the market having electronics placed on the top cover and subject to overheating and ageing, ours has a separate control box placed on the right side of the instrument.
Diffuser Calibration Apparatus
A useful equipment for those making lots of foaming tests since it permits to calibrate and recalibrate the expensive diffusers. The apparatus can be used to check both cylindrical (Mott) and spherical (Norton) diffusers for maximum pore diameter and permeability.
Digital Penetrometer To Bitumen,
The apparatus consists of a penetrometer with adjustable head combined with a gear that permits a fine adjustment of the cone position right upon the bitumen sample: the results are showed on a digital display placed, together with an electronic timer in an independent control box.Optionally, refrigerated baths of various sizes are available (please require related technical bulletin): by connecting the bath to the transfer dish it is possible to penetrate samples while immersed in water at 25°C or other test temperatures.
Dropping Point Of Lubricating Grease
The apparatus, in acc. with ASTM D 566 - IP 132 - ISO 2176, is a benchtop model which houses the components and a Panel PC with touch screen. A software running under Microsoft Windows embedded permits to select the test method and the test parameters, run the test automatically, store, retrieve and print data, diagnose and calibrate the instrument offering in the meanwhile all the features of Windows systems such as LAN connectivity. A unique cooling system permits to cool down quickly the heating furnace allowing to start a new test in a few minutes. The dropping point is the temperature at which the grease passes from a semisolid to a liquid state under the conditions of test. Cooperative testing indicates that in general, dropping points by test method D 566 is in agreement. The test, usually carried on with manually operated analyzers, has been totally automated with this instrument: in fact it provides automatically to regulate the heating rate, beginning with a 5.5°C/min rate and then reducing it to 1°C/min rate.
Ductility Machine
The apparatus, in acc with ASTM D 113, D 5976 - IP 32 - ISO 1208 - EN 13398, 13589, 13703 consists of a constant temperature bath capable to work in the range from -10 to 40 °C (thanks to a built-in cooling compressor) with an electrically powered tractor that pulls apart at a determined speed the two ends of two briquet specimens: the elongation is measured by means of a pointer on the tractor and a graduated scale fixed to the cover.
Existent Gum In Fuel
The apparatus consists of a benchtop case which houses an aluminium heating block. Two versions are available: one for the “Air Jet” test on gasoline and one for both the “Air and Steam Jet” tests with a built-in steam superheater. Steam generator and air blower are also available.
Flash And Fire Point Automatic Cleveland Tester With Barometric Correction Of The Result
Automatic equipment acc. to ASTM D 92 - IP 36 - ISO 2592 for both Flash and Fire Point that features electric heating, gas ignition with electric pilot flames, automatic fire extinguisher, barometric temperature correction, plus a touch-screen interface that permits to introduce test data, save and retrieve reports, print them and allow diagnostic and calibration.
Flash And Fire Point Automatic Cleveland Tester With Barometric Correction Of The Result
Automatic equipment acc. to ASTM D 92 - IP 36 - ISO 2592 that features electric heating, gas ignition with electric pilot flames, automatic fire extinguisher, barometric temperature correction plus a touch-screen interface that permits to introduce test data, save and retrieve reports, print them and allow diagnostic and calibration.
Flash Point Automatic Meter Abel Fix Barometric The Result
The only equipment on the market with the heating bath manufactured exactly as reported on the IP 33 - IP 170 method. The instrument features electric heating, stirrer and dipping mechanism plus a touch-screen interface that permits to introduce test data, save and retrieve reports, print them and allow diagnostic and calibration.
Flash Point Tester Cleveland Manual
Manual equipment realized exactly as reported in the ASTM D 92 - IP 36 - ISO 2592 methods and equipped with electric heating, digital temperature display and gas ignitor.
Flash Point Tester Cleveland Manual
Manual equipment realized exactly as reported in the ASTM D 92 - IP 36 - ISO 2592 methods and equipped with electric heating, digital temperature display and gas ignitor.
Flash Point Tester Pensky Martens
Manual equipment with the stove, air bath and top plate realized exactly as reported in the ASTM D 93 - IP 34 - ISO 2719 methods and equipped with electric heating, digital temperature display, gas ignitor and electric stirrer.
Glassware Corrosion Test
Innovative equipment acc. to ASTM D1384 with solid block heating, touch-screen interface and mass-flow controllers that permit to maintain a constant air flow even in case of fluctuation of inlet air pressure: temperature and air flow are recorded and plotted on a chart on the screen. The instrument is also fitted with a water distributor and sink for condensers cooling water and a device that permits to maintain the the condensers themselves in position while removing the sample containers at the end of the test.
Grease Worker
The apparatus is in acc. with ASTM D 217 - IP 50 - ISO 2137. Worked penetration results may be used to establish the consistency of lubricating greases after prolonged working. The change in worked penetration results on a grease after prolonged working are believed to be a measure of its shear stability under the conditions of the test. The electrically operated grease working machine consists of a geared motor for 60 strokes/min mounted on a aluminium base with clamps to fix the grease workers. The number of strokes, continuously showed on a display, can be preset to stop the worker after any required number of strokes up to 100,000.
High-Temp. Foaming Bath
Single-unit apparatus with two jackets acc. to ASTM D 6082 for tests at 150°C. Equipped with electronic temperature controller, variable area flowmeters, level and overtemp alarm. The instrument has a safety enclosure that avoids accidental contacts with the hot jar.
Hot Filtration
The apparatus consists of a support hosting two filtering units. A unique mechanism permits to the operator to stay far from hot parts of the instrument during the operations to avoid risks of burnings.
Hydrolytic Stability In Hydraulic Fluids
The apparatus consists of a benchtop oven with a turntable inside that can carry four or eight 200 ml Coca-Cola bottles. The turntable rotates the bottles at 5 rpm.
Loss On Heating Of Asphaltic Compounds And The Combined Effect Of Air And Heat On Bitumens,
The apparatus consists of a convection oven manufactured as described in the ASTM E 145 specification (type IB), suitable for temperatures up to 180°C and equipped with a rotating shelf inside. An electronic controlled motor with gear reducer mounted on the top of the oven rotates the shelf at 5.5 rpm.
Mechanical Demulsibility
The apparatus consists of a steel frame supporting the control box, the jar and an electric lift that permits to move the stirrer blade up and down in the test cylinder. The speed of the stirrer is continuously showed on a digital tachometer.
Oxidation And Corrosion
4-6-8 or 12-place apparatus acc. to FTMS 791 - 5308.4 with aluminum block heater and variable area dedicated flowmeters for each position. Versions with mass flow controllers and Panel PC also available, please contact us.
Oxidation Fuel Oil
4-6-8 or 12-place apparatus acc. to ASTM D 2274 - IP 388 with aluminum block heater and variable area dedicated flowmeters for each position. Versions with mass flow controllers and Panel PC also available, please contact us.
Oxidation Grease With Pc
New automatic benchtop equipment acc. to ASTM D 942 available in 2, 4 or 6-position versions, with aluminum block heating. Vessels are equipped with pressure transducers, cables and quick connectors while the touch-screen interface plots pressure and temperature data on a chart and allows user to enter, save, retrieve, print test reports and run diagnostic and calibration routines. Ethernet and USB ports permit to connect to LIMS or printers.
Oxidation Of Insulating Oils
New compact equipment acc. to ASTM D 2440, IEC 61125 (A, B and C) available in 4, 6, 8 or 12-position aluminum-block versions with mass-flow controllers and knob + display or touch-screen interface with the possibility to record and print test reports showing temperature and flow on a chart.
Oxidation Of Mineral Oils
4-6-8 or 12-place apparatus acc. to ASTM D 943 - IP 157 with aluminum block heater and variable area dedicated flowmeters for each position. Versions with mass flow controllers and Panel PC also available, please contact us.
Resistance To Oxidation Of Gasolines
New automatic benchtop equipment acc. to ASTM D 525 - D 873 available in 2, 4 or 6-position versions, with aluminum block heating. Vessels are equipped with pressure transducers, cables and quick connectors while the touch-screen interface plots pressure and temperature data on a chart and allows user to enter, save, retrieve, print test reports and run diagnostic and calibration routines. Automatic calculation of breaking point. Ethernet and USB ports permit to connect to LIMS or printers.
Rpvot Tfout
Floor-mounted, ASTM D 2272 - D 4742 automatic twin-unit equipment: one of the few equipment on the market respecting the 30 l heating oil per position ASTM prescription. Vessels are equipped with pressure transducers, cables and quick connectors while the touch-screen interface plots pressure and temperature data on a chart and allows user to enter, save, retrieve, print test reports and run diagnostic and calibration routines. Automatic detection of plateau and vessel life. Ethernet and USB ports permit to connect to LIMS or printers.
Steam Pressure In LPG
The apparatus consists of a floor mounted water bath with a support for three vapour pressure cylinders.
Steamed Gas
The apparatus consists of a floor mounted water bath with a support for three vapour pressure cylinders.
The Apparatus Determination Oxidation Stability Of Greases With Recorder
New automatic benchtop equipment acc. to ASTM D 942 available in 2, 4 or 6-position versions, with aluminum block heating. Vessels are equipped with pressure transducers, cables and quick connectors while the touch-screen interface plots pressure and temperature data on a chart and allows user to enter, save, retrieve, print test reports and run diagnostic and calibration routines. Ethernet and USB ports permit to connect to LIMS or printers.
Thermostatic Bath For Thermostatting Of Samples By Penetration,
The equipment, in acc with ASTM D 5 - D 217, consists of a compact benchtop circulation cooler to be placed below the bench supporting the penetrometer: thanks to a built-in cooling compressor, temperature can be maintained in a range from 0 to 50°C with 0.1°C precision.
Thermostatic Bath For Thermostatting Of Samples By Penetration,
The equipment, in acc with ASTM D 5 - D 217, consists of a compact benchtop circulation cooler to be placed below the bench supporting the penetrometer: thanks to a built-in cooling compressor, temperature can be maintained in a range from 0 to 50°C with 0.1°C precision.
Viscosity Determination
The apparatus consists of a benchtop steel case containing a pyrex jar, 330 mm deep, that permits the use of a wide range of viscometer tubes. Up to six viscometer tubes can be inserted on a turntable that allows to carry in the front of the jar the tube on which the operator is working on.