CHEMPARTSMIDDLE EAST FZCMEDICAL & LABORATORY SUPPLIES
CartSign inRegister+971 6 5574047

[HOME]/[PRODUCTS]/INSTRUMENTS

Instruments

Analytical instruments & equipment

XRF, flash point, distillation, mercury, NMR, FTIR, viscosity and more — supplied, installed and serviced in-region. Filter by brand and industry, then request a quote.

[256] instruments · showing 217–240
STEALTH EHC
Fluitec

STEALTH EHC

This dry gas blanketing system is designed to keep moisture out especially for Phosphate ester systems. Moisture is the root cause for many contamination issues in EHC systems. Because phosphate esters are hydroscopic, moisture control is a critical step in phosphate ester maintenance. Stealth EHC™ uses patented technology that removes moisture from phosphate ester fluids by introducing a steady stream of clean, dry air in the reservoir. This enhances reservoir breathing systems by actively and continuously purging and dehydrating the reservoir headspace and removing water from the fluid. Cont

Price on request
Steam Pressure In LPG
Scavini

Steam Pressure In LPG

The apparatus consists of a floor mounted water bath with a support for three vapour pressure cylinders.

Price on request
Steamed Gas
Scavini

Steamed Gas

The apparatus consists of a floor mounted water bath with a support for three vapour pressure cylinders.

Price on request
T-730 pH/mV/Conductivity/DO Meter
Peak Instruments

T-730 pH/mV/Conductivity/DO Meter

Multi-parameter analyzer for high precision measurement in laboratory covering 10 kinds of electrochemical parameters like pH, conductivity and dissolved oxygen. Suitable for the fields of petroleum, chemical, pharmacy, power plants and environmental protection, also widely used in areas of education and scientific research.

Price on request
T2FM Ferrography System
Biolab

T2FM Ferrography System

T2FM Ferrography System

Price on request
Tag Closed Cup Flash Point Tester (100 Series)
Tanaka

Tag Closed Cup Flash Point Tester (100 Series)

atg-100 is an automated Tag Closed flash point tester.

Price on request
Tag Closed Cup Flash Point Tester (8 Series)
Tanaka

Tag Closed Cup Flash Point Tester (8 Series)

atg-8 is an automated Tag Closed flash point tester.

Price on request
TAG Flash Point Tester
Biolab

TAG Flash Point Tester

TAG Flash Point Tester

Price on request
Tamson ASTM D1881 Foaming Bath (Single)
Tamson

Tamson ASTM D1881 Foaming Bath (Single)

The Tamson ASTM D1881 Foaming Bath is available in the following voltages/frequencies:

Price on request
Tamson ASTM D6082 High Temperature Foaming Bath
Tamson

Tamson ASTM D6082 High Temperature Foaming Bath

The Tamson high temperature foaming bath can be used to test the foaming characteristics of lubrication oils conform ASTM D6082 and IP 453. The apparatus comes with a bath that can be operated at 150°C as required by the test method. A rack with two flowmeters is standard supplied. The bath has four openings for foaming cylinders. The rack can be used to hold up to four foaming cylinders. Also, the stoppers and optional dryer can be mounted on this rack. The foaming bath has a cylindrical glass jar with a drain and is equipped with a metal case with removable windows to guarantee safe operatio

Price on request
Tamson ASTM D7840 Foaming Bath (Single)
Tamson

Tamson ASTM D7840 Foaming Bath (Single)

The Tamson ASTM D892 Foaming Bath is available in the following voltages/frequencies:

Price on request
Tamson ASTM D892 Foaming Bath (Dual)
Tamson

Tamson ASTM D892 Foaming Bath (Dual)

The Tamson dual foaming bath can be used to test the foaming characteristics of lubrication oils conform ASTM D892. The apparatus comes with two baths that can interchangebly be operated at 24°C and 93.5°C. A rack with flowmeters is supplied. The bath has four openings for foaming cylinders. The rack can be used to hold up to four foaming cylinders, for example between sequence II and III of the test method. Also, the stoppers and optional dryer can be mounted on this rack. The baths are equipped with a metal case for safe operation. Furthermore, the bath offers an excellent temperature stabil

Price on request
Tamson ASTM D892 Foaming Bath (Single)
Tamson

Tamson ASTM D892 Foaming Bath (Single)

The Tamson foaming bath can be used to test the foaming characteristics of lubrication oils conform ASTM D892. The apparatus comes with two baths that can interchangebly be operated at 24°C and 93.5°C. A rack with two flowmeters is supplied. The bath has four openings for foaming cylinders. The rack can be used to hold up to four foaming cylinders, for example between sequence II and III of the test method. Also, the stoppers and optional dryer can be mounted on this rack. The baths are equipped with a metal case for safe operation. Furthermore, the bath offers an excellent temperature stabili

Price on request
TC16 used for ASTM-D1796
Tamson

TC16 used for ASTM-D1796

The TC16 ASTM D1796 bath is designed to preheat the centrifuge cones as required when follwing the determination for water and sediment in fuel oils (ASTM D1796) or crude oils (ASTM D4007) by the centrifuge method. The robust TC16 is according to the requirements of the ASTM D1796 test method where a water bath is prescribed to preheat the cone-shaped centrifuge tubes. With the levelling platform and special designed rack, nine 8" cone shaped centrifuge tubes can be immersed up to the 100 mL mark, as prescribed in the ASTM methods.

Price on request
TC16 used for ASTM-D70
Tamson

TC16 used for ASTM-D70

The TC16 ASTM D70 is designed for specific gravity and density by pycnometer tests. The bath is suitable for tests conform ASTM D70, IP 190 and ISO 3838. The brackets inside the TC16 can offer maximum nine positions for either Hubbard or Gay-Lussac pycnometers. The brackets and ridge keep the pycnometers in place during the test. The TC16 is equipped with a cooling coil to allow the use of counter-cooling. This cooling coil can be connectd to a TLC15-5 circulator when working at +15°C or +25°C.

Price on request
TC40 Silver Corrosion Bath
Tamson

TC40 Silver Corrosion Bath

This test method specifies the determination of the corrosive tendencies towards silver of aviation turbine fuel, automotive spark-ignition engine oils or automotive gasoline. The result is classified as an integer in the range 0 to 4. The bath offers place for 18 test positions. The temperature range is from ambient +5°C to 250°C. The bath can also be used for copper corrosion tests, please see our specification sheet for ASTM D130 and related methods.

Price on request
TCC-B D97 D2500 bath
Tamson

TCC-B D97 D2500 bath

The TCC-B D97 D2500 is a bath for manual cloud and pour point tests conform ASTM D97 and ASTM D2500. The TCC-B can be equipped with a cover that offers position for four jackets. The bath can be delivered with all accessories needed for manual cloud and pour point tests. The TCC-B is a single adjustable bath and therefore a very budget-friendly solution to test the cloud and pour point down to -85°C.

Price on request
Test your oils at high temperatures to ASTM 6082!
Normalab

Test your oils at high temperatures to ASTM 6082!

FOAM HT evaluates the foaming characteristics of lubricating oils up to 150°C according to ASTM D6082, with four test sequences in a single bath.

Price on request
Test your oils with FOAM 1 & 2
Normalab

Test your oils with FOAM 1 & 2

These devices evaluate the foaming characteristics of lubricating oils with tests at 24 °C and 93.5 °C thanks to 2 test positions per bath.

Price on request
The Apparatus Determination Oxidation Stability Of Greases With Recorder
Scavini

The Apparatus Determination Oxidation Stability Of Greases With Recorder

New automatic benchtop equipment acc. to ASTM D 942 available in 2, 4 or 6-position versions, with aluminum block heating. Vessels are equipped with pressure transducers, cables and quick connectors while the touch-screen interface plots pressure and temperature data on a chart and allows user to enter, save, retrieve, print test reports and run diagnostic and calibration routines. Ethernet and USB ports permit to connect to LIMS or printers.

Price on request
Thermostatic Bath For Thermostatting Of Samples By Penetration,
Scavini

Thermostatic Bath For Thermostatting Of Samples By Penetration,

The equipment, in acc with ASTM D 5 - D 217, consists of a compact benchtop circulation cooler to be placed below the bench supporting the penetrometer: thanks to a built-in cooling compressor, temperature can be maintained in a range from 0 to 50°C with 0.1°C precision.

Price on request
Thermostatic Bath For Thermostatting Of Samples By Penetration,
Scavini

Thermostatic Bath For Thermostatting Of Samples By Penetration,

The equipment, in acc with ASTM D 5 - D 217, consists of a compact benchtop circulation cooler to be placed below the bench supporting the penetrometer: thanks to a built-in cooling compressor, temperature can be maintained in a range from 0 to 50°C with 0.1°C precision.

Price on request
TLB50 ASTM D7501 cold soak bath
Tamson

TLB50 ASTM D7501 cold soak bath

The Tamson TLB50 ASTM D7501 cold soak bath is a bath to soak the samples according to ASTM D7501, IP PM EA, CEN N 403 and CGSB 3.0 No. 142.. The bath is equipped with integrated cooling and has a very large capacity to cold soak samples at temperatures ranging from -5°C up to +80°C. The benchtop bath with integrated cooling can replace the combination of a water bath with an external cooling circulator. This not only saves bench space, but also costs because of its high cooling efficiency. The TLB50 can be connected to a PC using the RS232 connection. The PC can control the setpoint temperatur

Price on request
TLC40-14 D97 D2500 bath
Tamson

TLC40-14 D97 D2500 bath

The TLC40-14 D97 D2500 is a bath for manual cloud and pour point tests conform ASTM D97 and ASTM D2500. The TLC40-14 can be equipped with a cover that offers position for six jackets. The bath can be delivered with all accessories needed for manual cloud and pour point tests. The TLC40-14 is a single adjustable bath and therefore a very budget-friendly solution to test the cloud and pour point down to -40 C.

Price on request
Need help shortlisting?

Tell us your requirement.

Send us the method, model or part you need. We'll come back with the right shortlist — usually within the working day.

WhatsApp +971 55 756 6123Use the contact form
WhatsApp